ts7800 series 3-terminal fixed positive voltage regulator 1/10 version: d12 to - 220 ito - 220 general description the ts7800 series voltage regulators are monolithic integrated circuits designed as fixed-voltage regu lators for a wide variety of applications including local, on-ca rd regulation. these regulators employ internal cur rent limiting, thermal shutdown, and safe-area compensation. with adequate heatsink they can deliver output currents up to 1 ampere. although designed primarily as a fixed volt age regulator, these devices can be used with exter nal components to obtain adjustable voltages and curren ts. features output voltage range 5 to 24v output current up to 1a no external components required internal thermal overload protection internal short-circuit current limiting output transistor safe-area compensation output voltage offered in 4% tolerance standard application circuit a common ground is required between the input and th e output voltages. the input voltage must remain typi cally 2.0v above the output voltage even during the low po int on the input ripple voltage. xx = these two digits of the type number indicate vo ltage. * = cin is required if regulator is located an appr eciable distance from power supply filter. ** = co is not needed for stability; however, it does improve transient response . ordering information part no. package packing ts78 xx cz c0 to-220 50pcs / tube ts78 xx ci c0 ito-220 50pcs / tube note: where xx denote voltage option, available are: 05 =5v, 06 =6v, 08 =9v, 09 =9v, 10 =10v 12 =12v, 15 =15v, 18 =18v, 24 =24v absolute maximum rating (ta = 25 o c unless otherwise noted) parameter symbol limit unit input voltage v out =5~18v v in 35 v v out =24v 40 output current i out internal limited power dissipation p d internal limited operating junction temperature t j 0~+125 o c storage temperature range t stg -65~+150 o c thermal resistance - junction to case to-220 r ? jc 5 o c/w ito-220 5 thermal resistance - junction to ambient to-220 r ? ja 50 o c/w ito-220 60 note: absolute maximum ratings are those values beyond w hich damage to the device may occur. functional operation under these conditio n is not implied. pin definition : 1. input 2. ground (tab) 3. output
ts7800 series 3-terminal fixed positive voltage regulator 2/10 version: d12 ts7805 electrical characteristics (vin=10v, iout=500ma, 0 o c tj 125 o c, cin=0.33uf, cout=0.1uf; unless otherwise specifi ed.) parameter symbol test condition min typ max unit output voltage vout tj=25 o c 4.80 5 5.20 v 7.5v vin 20v, 10ma iout 1a, pd 15w 4.75 5 5.25 line regulation regline tj=25 o c 7.5v vin 25v -- 3 100 mv 8v vin 12v -- 1 50 load regulation regload tj=25 o c 10ma iout 1a -- 15 100 250ma iout 750ma -- 5 50 quiescent current iq iout=0, tj=25 o c -- 4.2 8 ma quiescent current change ? iq 7.5v vin 25v -- -- 1.3 10ma iout 1a -- -- 0.5 output noise voltage vn 10hz f 100khz, tj=25 o c -- 40 -- v ripple rejection ratio rr f=120hz, 8v vin 18v 62 78 -- db voltage drop vdrop iout=1.0a, tj=25 o c -- 2 -- v output resistance rout f=1khz -- 17 -- m w output short circuit current ios tj=25 o c -- 750 -- ma peak output current io peak tj=25 o c -- 2.2 -- a temperature coefficient of output voltage ? vout/ ? tj iout=10ma, 0 o c tj 125 o c -- -0.6 -- mv/ o c ts7806 electrical characteristics (vin=11v, iout=500ma, 0 o c tj 125 o c, cin=0.33uf, cout=0.1uf; unless otherwise specifi ed.) parameter symbol test condition min typ max unit output voltage vout tj=25 o c 5.75 6 6.25 v 8.5v vin 21v, 10ma iout 1a, pd 15w 5.7 6 6.3 line regulation regline tj=25 o c 8.5v vin 25v -- 5 120 mv 9v vin 13v -- 1.5 60 load regulation regload tj=25 o c 10ma iout 1a -- 14 120 250ma iout 750ma -- 4 60 quiescent current iq iout=0, tj=25 o c -- 4.3 8 ma quiescent current change ? iq 8.5v vin 25v -- -- 1.3 10ma iout 1a -- -- 0.5 output noise voltage vn 10hz f 100khz, tj=25 o c -- 45 -- uv ripple rejection ratio rr f=120hz, 9v vin 19v 59 75 -- db voltage drop vdrop iout=1.0a, tj=25 o c -- 2 -- v output resistance rout f=1khz -- 19 -- m w output short circuit current ios tj=25 o c -- 550 -- ma peak output current io peak tj=25 o c -- 2.2 -- a temperature coefficient of output voltage ? vout/ ? tj iout=10ma, 0 o c tj 125 o c -- -0.7 -- mv/ o c pulse testing techniques are used to maintain the junction temperature as close to the ambient temper ature as possible, and thermal effects must be taken into ac count separately. this specification applies only for dc power dissi pation permitted by absolute maximum ratings.
ts7800 series 3-terminal fixed positive voltage regulator 3/10 version: d12 ts7808 electrical characteristics vin=14v, iout=500ma, 0 o c tj 125 o c, cin=0.33uf, cout=0.1uf; unless otherwise specifi ed.) parameter symbol test condition min typ max unit output voltage vout tj=25 o c 7.69 8 8.32 v 10.5v vin 23v, 10ma iout 1a, pd 15w 7.61 8 8.40 line regulation regline tj=25 o c 10.5v vin 25v -- 6 160 mv 11v vin 17v -- 2 80 load regulation regload tj=25 o c 10ma iout 1a -- 12 160 250ma iout 750m a -- 4 80 quiescent current iq iout=0, tj=25 o c -- 4.3 8 ma quiescent current change ? iq 10.5v vin 25v -- -- 1 10ma iout 1a -- -- 0.5 output noise voltage vn 10hz f 100khz, tj=25 o c -- 52 -- v ripple rejection ratio rr f=120hz, 11v vin 21v 56 72 -- db voltage drop vdrop iout=1.0a, tj=25 o c -- 2 -- v output resistance rout f=1khz -- 16 -- m w output short circuit current ios tj=25 o c -- 450 -- ma peak output current io peak tj=25 o c -- 2.2 -- a temperature coefficient of output voltage ? vout/ ? tj iout=10ma, 0 o c tj 125 o c -- -0.8 -- mv/ o c ts7809 electrical characteristics (vin=15v, iout=500ma, 0 o c tj 125 o c, cin=0.33uf, cout=0.1uf; unless otherwise specifi ed.) parameter symbol test condition min typ max unit output voltage vout tj=25 o c 8.65 9 9.36 v 11.5v vin 23v, 10ma iout 1a, pd 15w 8.57 9 9.45 line regulation regline tj=25 o c 11.5v vin 26v -- 6 180 mv 12v vin 17v -- 2 90 load regulation regload tj=25 o c 10ma iout 1a -- 12 180 250ma iout 750ma -- 4 90 quiescent current iq iout=0, tj=25 o c -- 4.3 8 ma quiescent current change ? iq 11.5v vin 26v -- -- 1 10ma iout 1a -- -- 0.5 output noise voltage vn 10hz f 100khz, tj=25 o c -- 52 -- uv ripple rejection ratio rr f=120hz, 12v vin 22v 55 72 -- db voltage drop vdrop iout=1.0a, tj=25 o c -- 2 -- v output resistance rout f=1khz -- 16 -- m w output short circuit current ios tj=25 o c -- 450 -- ma peak output current io peak tj=25 o c -- 2.2 -- a temperature coefficient of output voltage ? vout/ ? tj iout=10ma, 0 o c tj 125 o c -- -1 -- mv/ o c pulse testing techniques are used to maintain the junction temperature as close to the ambient temper ature as possible, and thermal effects must be taken into ac count separately. this specification applies only for dc power dissi pation permitted by absolute maximum ratings.
ts7800 series 3-terminal fixed positive voltage regulator 4/10 version: d12 ts7810 electrical characteristics vin=16v, iout=500ma, 0 o c tj 125 o c, cin=0.33uf, cout=0.1uf; unless otherwise specifi ed.) parameter symbol test condition min typ max unit output voltage vout tj=25 o c 9.6 10 10.4 v 12.5v vin 25v, 10ma iout 1a, pd 15w 9.5 10 10.5 line regulation regline tj=25 o c 12.5v vin 28v -- 7 200 mv 13v vin 17v -- 2 100 load regulation regload tj=25 o c 10ma iout 1a -- 12 200 250ma iout 750m a -- 4 100 quiescent current iq iout=0, tj=25 o c -- 4.3 8 ma quiescent current change ? iq 12.5v vin 28v -- -- 1 10ma iout 1a -- -- 0.5 output noise voltage vn 10hz f 100khz, tj=25 o c -- 70 -- v ripple rejection ratio rr f=120hz, 13v vin 23v 55 71 -- db voltage drop vdrop iout=1.0a, tj=25 o c -- 2 -- v output resistance rout f=1khz -- 18 -- m w output short circuit current ios tj=25 o c -- 400 -- ma peak output current io peak tj=25 o c -- 2.2 -- a temperature coefficient of output voltage ? vout/ ? tj iout=10ma, 0 o c tj 125 o c -- -1 -- mv/ o c ts7812 electrical characteristics (vin=19v, iout=500ma, 0 o c tj 125 o c, cin=0.33uf, cout=0.1uf; unless otherwise specifi ed.) parameter symbol test condition min typ max unit output voltage vout tj=25 o c 11.53 12 12.48 v 14.5v vin 27v, 10ma iout 1a, pd 15w 11.42 12 12.60 line regulation regline tj=25 o c 14.5v vin 30v -- 10 240 mv 15v vin 19v -- 3 120 load regulation regload tj=25 o c 10ma iout 1a -- 12 240 250ma iout 750ma -- 4 120 quiescent current iq tj=25 o c, iout=0 -- 4.3 8 ma quiescent current change ? iq 14.5v vin 30v -- -- 1 10ma iout 1a -- -- 0.5 output noise voltage vn 10hz f 100khz, tj=25 o c -- 75 -- uv ripple rejection ratio rr f=120hz, 15v vin 25v 55 71 -- db voltage drop vdrop iout=1.0a, tj=25 o c -- 2 -- v output resistance rout f=1khz -- 18 -- m w output short circuit current ios tj=25 o c -- 350 -- ma peak output current io peak tj=25 o c -- 2.2 -- a temperature coefficient of output voltage ? vout/ ? tj iout=10ma, 0 o c tj 125 o c -- -1 -- mv/ o c pulse testing techniques are used to maintain the junction temperature as close to the ambient temper ature as possible, and thermal effects must be taken into ac count separately. this specification applies only for dc power dissi pation permitted by absolute maximum ratings.
ts7800 series 3-terminal fixed positive voltage regulator 5/10 version: d12 ts7815 electrical characteristics vin=23v, iout=500ma, 0 o c tj 125 o c, cin=0.33uf, cout=0.1uf; unless otherwise specifi ed.) parameter symbol test condition min typ max unit output voltage vout tj=25 o c 14.42 15 15.60 v 17.5v vin 30v, 10ma iout 1a, pd 15w 14.28 15 15.75 line regulation regline tj=25 o c 17.5v vin 30v -- 12 300 mv 18v vin 22v -- 3 150 load regulation regload tj=25 o c 10ma iout 1a -- 12 300 250ma iout 750ma -- 4 150 quiescent current iq tj=25 o c, iout=0 -- 4.3 8 ma quiescent current change ? iq 17.5v vin 30v -- -- 1 10ma iout 1a -- -- 0.5 output noise voltage vn 10hz f 100khz, tj=25 o c -- 90 -- v ripple rejection ratio rr f=120hz, 18v vin 28v 54 70 -- db voltage drop vdrop iout=1.0a, tj=25 o c -- 2 -- v output resistance rout f=1khz -- 19 -- m w output short circuit current ios tj=25 o c -- 230 -- ma peak output current io peak tj=25 o c -- 2.2 -- a temperature coefficient of output voltage ? vout/ ? tj iout=10ma, 0 o c tj 125 o c -- -1 -- mv/ o c ts7818 electrical characteristics (vin=24v, iout=500ma, 0 o c tj 125 o c, cin=0.33uf, cout=0.1uf; unless otherwise specifi ed.) parameter symbol test condition min typ max unit output voltage vout tj=25 o c 17.30 18 18.72 v 21v vin 33v, 10ma iout 1a, pd 15w 17.14 18 18.90 line regulation regline tj=25 o c 21v vin 33v -- 15 360 mv 22v vin 26v -- 5 180 load regulation regload tj=25 o c 10ma iout 1a -- 12 360 250ma iout 750ma -- 4 180 quiescent current iq tj=25 o c, iout=0 -- 4.5 8 ma quiescent current change ? iq 21v vin 33v -- -- 1 10ma iout 1a -- -- 0.5 output noise voltage vn 10hz f 100khz, tj=25 o c -- 110 -- uv ripple rejection ratio rr f=120hz, 21v vin 31v 54 70 -- db voltage drop vdrop iout=1.0a, tj=25 o c -- 2 -- v output resistance rout f=1khz -- 22 -- m w output short circuit current ios tj=25 o c -- 200 -- ma peak output current io peak tj=25 o c -- 2.2 -- a temperature coefficient of output voltage ? vout/ ? tj iout=10ma, 0 o c tj 125 o c -- -1 -- mv/ o c pulse testing techniques are used to maintain the junction temperature as close to the ambient temper ature as possible, and thermal effects must be taken into ac count separately. this specification applies only for dc power dissi pation permitted by absolute maximum ratings.
ts7800 series 3-terminal fixed positive voltage regulator 6/10 version: d12 ts7824 electrical characteristics vin=33v, iout=500ma, 0 o c tj 125 o c, cin=0.33uf, cout=0.1uf; unless otherwise specifi ed.) parameter symbol test condition min typ max unit output voltage vout tj=25 o c 23.07 24 24.96 v 27v vin 38v, 10ma iout 1a, pd 15w 22.85 24 25.20 line regulation regline tj=25 o c 27v vin 38v -- 18 480 mv 28v vin 32v -- 6 240 load regulation regload tj=25 o c 10ma iout 1a -- 12 480 250ma iout 750ma -- 4 240 quiescent current iq iout=0, tj=25 o c -- 4.6 8 ma quiescent current change ? iq 27v vin 38v -- -- 1 10ma iout 1a -- -- 0.5 output noise voltage vn 10hz f 100khz, tj=25 o c -- 170 -- v ripple rejection ratio rr f=120hz, 27v vin 37v 54 70 -- db voltage drop vdrop iout=1.0a, tj=25 o c -- 2 -- v output resistance rout f=1khz -- 28 -- m w output short circuit current ios tj=25 o c -- 150 -- ma peak output current io peak tj=25 o c -- 2.2 -- a temperature coefficient of output voltage ? vout/ ? tj iout=10ma, 0 o c tj 125 o c -- -1.5 -- mv/ o c pulse testing techniques are used to maintain the junction temperature as close to the ambient temper ature as possible, and thermal effects must be taken into ac count separately. this specification applies only for dc power dissi pation permitted by absolute maximum ratings.
ts7800 series 3-terminal fixed positive voltage regulator 7/10 version: d12 electrical characteristics curve figure 1. peak output current as a function of input-output differential voltage figure 2. ripple rejection as a function of output voltage figure 3. ripple rejection as a function of frequency figure 4. output voltage as a function of junction temperature figure 5. output impedance as a function of output voltage figure 6. quiescent current as a function of temperature
ts7800 series 3-terminal fixed positive voltage regulator 8/10 version: d12 to-220 mechanical drawing marking diagram xx = output voltage ( 05 =5v, 06 =6v, 08 =8v, 09 =9v, 10 =10v, 12 =12v, 15 =15v, 18 =18v, 24 =24v) y = year code m = month code ( a =jan, b =feb, c =mar, d =apl, e =may, f =jun, g =jul, h =aug, i =sep, j =oct, k =nov, l =dec) l = lot code cz = package code for to -220 to-220 dimension dim millimeters inches min max min max a 9.31 10.50 0.367 0.413 b 3.74 3.91 0.147 0.154 c 2.36 3.24 0.093 0.128 d 2.22 3.22 0.087 0.127 e 0.78 0.98 0.031 0.039 f -- 2.65 -- 0.104 g -- 5.30 -- 0.209 h 12.32 13.88 0.485 0.546 i 8.74 9.26 0.344 0.365 j 15.07 16.47 0.593 0.648 k 4.35 4.65 0.171 0.183 l 1.16 1.40 0.046 0.055 m 28.37 30.35 1.117 1.195 n 1.78 2.67 0.070 0.105 o 0.255 0.610 0.010 0.024 p 5.75 7.65 0.226 0.301
ts7800 series 3-terminal fixed positive voltage regulator 9/10 version: d12 ito-220 mechanical drawing marking diagram xx = output voltage ( 05 =5v, 06 =6v, 08 =8v, 09 =9v, 10 =10v, 12 =12v, 15 =15v, 18 =18v, 24 =24v) y = year code m = month code ( a =jan, b =feb, c =mar, d =apl, e =may, f =jun, g =jul, h =aug, i =sep, j =oct, k =nov, l =dec) l = lot code ci = package code for ito -220 ito-220 dimension dim millimeters inches min max min max a 9.96 10.36 0.392 0.407 b 6.20 (typ.) 0.244 (typ.) c 2.20 (typ.) 0.087 (typ.) d 1.40 (typ.) 0.055 (typ.) e 15.07 16.07 0.593 0.632 f 0.80 (typ.) 0.031 (typ.) g 2.44 2.64 0.096 0.104 h 13.08 13.48 0.514 0.530 i 1.47 (max.) 0.057 (max.) j 3.20 3.40 0.125 0.133 k 4.60 4.80 0.181 0.188 l 1.15 (typ.) 0.045 (typ.) m 2.44 2.64 0.096 0.104 n 2.60 2.80 0.102 0.110 o 6.55 6.65 0.258 0.262
ts7800 series 3-terminal fixed positive voltage regulator 10/10 version: d12 notice specifications of the products displayed herein are subject to change without notice. tsc or anyone on its behalf, assumes no responsibility or liability for any erro rs or inaccuracies. information contained herein is intended to provide a product description only. no license, express or implied, to any intellectual property rights is granted by this document. except as provided in tscs terms and co nditions of sale for such products, tsc assumes no liability wh atsoever, and disclaims any express or implied warr anty, relating to sale and/or use of tsc products includi ng liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, cop yright, or other intellectual property right. the products shown herein are not designed for use in medical, life-saving, or life-sustaining applica tions. customers using or selling these products for use i n such applications do so at their own risk and agr ee to fully indemnify tsc for any damages resulting from such i mproper use or sale.
|
